Product Code:SAE J772
Title:Clearance Envelopes for Six-Bolt, Eight-Bolt, and Rear Truck Transmission Mounted Power Takeoffs
Issuing Committee:Truck And Bus Power Take-Off Committee
Scope:The purpose of this document is to provide dimensions of clearance envelopes for various types of six-bolt regular-duty, eight-bolt heavy-duty, and side- and rear-mounted truck transmission power takeoffs. These envelopes are applicable to the clearance required immediately adjacent to the power takeoff openings on truck transmissions. Clearance envelopes are provided for the purpose of documenting current practice. It must be recognized that many current designs do not provide these clearances in all orientations and variations. New transmission and power takeoff designs should attempt to adhere to these envelopes where practical, but they should not be construed to be design restrictive; ultimately, the actual power takeoff clearance must be established for each application. In order to provide realistic envelope sizes, there are seven basic 脪types脫 of side-mounted P.T.O. envelopes and rear-mounted envelopes as shown in Table 1.All envelopes shown are basic and can be reversed for output to the front or rear of the vehicle. On Types II, III, IV, and VI, output shaft locations can additionally be reversed from that shown to the opposite side of the P.T.O. opening centerline. Driveline envelopes, front or rear, above or below centerline of opening as required, must be a cylinder of the minimum diameter shown and fall within the 15 degree maximum half-cone extending vertically up and down and horizontally outward from the driveline cone apex, for a distance equivalent to that required to bring the P.T.O. driveline beyond points of interference so that auxiliary equipment can be driven.Clearance should be provided on six-bolt openings on mechanical transmissions for Types I, II, and III with Types I and II being a minimum requirement.【英文标准名称】:Wastewatertreatmentplants-Part10:Safetyprinciples;GermanversionEN12255-10:2000
【原文标准名称】:污水处理厂.第10部分:安全性原则
【标准号】:EN12255-10-2000
【标准状态】:现行
【国别】:
【发布日期】:2001-03
【实施或试行日期】:
【发布单位】:欧洲标准学会(EN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:污水处理厂;建筑系统构件;选址;污水处理;施工原则;可及性;污水净化;规范(验收);;职业安全;水常规(实验);结构要求;污水;污水分类;水常规;抽油装置;建筑工程;计划;安全要求;安全;安全;定义;定义;设备;安全工程;爆炸区域;污水净化工厂;污水处理工厂;人体保护;工作场所安全;建设工程
【英文主题词】:Accessibility;Constructionrequirements;Constructionsystemsparts;Constructionworks;Constructions;Definition;Definitions;Equipment;Explosionarea;Occupationalsafety;Planning;Principlesofconstruction;Protectionofpersons;Pumpinginstallation;Safety;Safetyengineering;Safetyrequirements;Sewage;Sewageclarification;Sewagepurification;Sewagepurificationplant;Sewagetreatment;Sewagetreatmentplants;Sewagetreatmentworks;Siting;Specification(approval);Warningsystem;Waterpractice;Workplacesafety
【摘要】:
【中国标准分类号】:J88;P41
【国际标准分类号】:13_060_30
【页数】:16P.;A4
【正文语种】:英语